Renovimo
An empty renovated living room with white crown molding along the ceiling, baseboard on gray walls and arched doorways

Engineering calculator

Miter and crown molding angle calculator

In a square 90° corner, flat trim is mitered at 45°. Crown molding lying flat on the saw needs a compound cut instead: a 31.62° miter with a 33.86° bevel for 52/38 crown, 35.26° with 30.00° for 45/45 crown — or a plain 45° miter with the crown nested upside down against the fence. Enter the corner you measured, inside or outside, and this calculator gives the saw settings, which edge is the long point, the cut length for the wall and a drawing of every cut.

Enter your corner

Miter angle calculator: the corner and the trim

Measure the corner with an angle finder or a sliding bevel, a leg on each wall. Walls are rarely a true 90°: a corner that reads 92° changes every setting below.

The wall run

The length of wall this piece covers, corner to corner along the wall (to the outside corner where the wall turns one). One end is the corner above; tell it the other.

Colors for the 3D

Code note. Trim is finish work: the building code sets no limits on how it is cut. One rule touches where it goes: around a masonry fireplace, no combustible trim within 6 in of the opening, and within 12 in it may project no more than ⅛ in for each inch of distance from the opening (IRC 2021 R1001.11); a factory-built fireplace follows its listing.

Quick answers

What angle do you cut crown molding?

What are the miter and bevel for crown molding in a 90° corner? Lying flat on a compound miter saw, crown takes two settings: miter = arctan(sin spring ÷ tan(corner ÷ 2)) and bevel = arcsin(cos spring × cos(corner ÷ 2)), where the spring angle is the tilt of the crown's back off the wall. For 52/38 crown (38° spring) in a 90° corner that is 31.62° miter and 33.86° bevel; for 45/45 crown, 35.26° and 30.00°; for 38/52 crown, 38.24° and 25.81°. Nested upside down instead — ceiling edge on the table, wall edge against the fence — any crown is cut at a plain 45° miter with no bevel. Flat trim such as baseboard and casing is mitered at 90° − corner ÷ 2: 45° in a square corner, 22.5° in a 135° bay.

Crown molding angle chart by corner

Saw settings for the corner angle measured between the wall faces. The same numbers serve an inside and an outside corner; only the side of the blade and the long point change. The flat-trim column is also the miter for crown cut nested, upside down against the fence.

Corner Flat trim / nested miter 38° crown miter / bevel 45° crown miter / bevel 52° crown miter / bevel
60° 60.00° 46.84° / 43.03° 50.77° / 37.76° 53.77° / 32.22°
88° 46.00° 32.52° / 34.53° 36.21° / 30.57° 39.21° / 26.29°
90° 45.00° 31.62° / 33.86° 35.26° / 30.00° 38.24° / 25.81°
92° 44.00° 30.73° / 33.19° 34.33° / 29.42° 37.27° / 25.32°
120° 30.00° 19.57° / 23.20° 22.21° / 20.70° 24.46° / 17.93°
135° 22.50° 14.31° / 17.55° 16.32° / 15.70° 18.08° / 13.63°
150° 15.00° 9.37° / 11.77° 10.73° / 10.55° 11.92° / 9.17°

Miter angle for a frame of n sides

Every joint in a regular frame is 180° ÷ the number of sides, cut on both ends of each piece, so the cuts add up to 360°.

Sides Shape Miter Frame corner
3 Triangle 60.00° 60.00°
4 Square or rectangle 45.00° 90.00°
5 Pentagon 36.00° 108.00°
6 Hexagon 30.00° 120.00°
8 Octagon 22.50° 135.00°
10 Decagon 18.00° 144.00°
12 Dodecagon 15.00° 150.00°
A carpenter marking a board at his bench, with a miter saw blade in the foreground

Based on your result

What you'll need to cut miters and crown

A miter saw that bevels does every cut on this page; a coping saw finishes inside corners on paint-grade work.

Molding
Stock lengths for the wall, with room to recut
Calculate above
Compound miter saw Amazon
Miter and bevel scales; how tall a crown it nests depends on its fence height
—
Angle finder or sliding bevel Amazon
Reads the real corner before the first cut
1
Coping saw Amazon
For coped inside corners on crown and baseboard
1
Brad nailer, 18 ga Amazon
2 in brads into studs, plates, joists or blocking
1
Wood glue or CA glue Amazon
On outside miters and frame joints
1
Paintable caulk and filler Amazon
Wall and ceiling lines, nail holes
1 tube each

As an Amazon Associate I earn from qualifying purchases.

The maths

How the crown molding angle is worked out

Both pieces of a corner are cut on the plane that splits the corner in half. Flat trim stands square on the saw, so that plane is a simple miter. Crown leans off the wall at its spring angle, so when it lies flat the same plane crosses it at a compound angle.

flat trim miter = 90° − corner ÷ 2
crown miter (flat) = arctan(sin spring ÷ tan(corner ÷ 2))
crown bevel (flat) = arcsin(cos spring × cos(corner ÷ 2))
crown nested = 90° − corner ÷ 2, bevel 0°
drop = width × cos spring, projection = width × sin spring
face edge = wall length ∓ depth ÷ tan(corner ÷ 2) per end
frame miter = 180° ÷ sides

The crown formulas are the standard ones (Wikipedia, "Crown molding", angle calculations) and are checked in the page's tests against the cut plane worked out in 3D.

  1. 01

    Measure the corner

    An angle finder with a leg on each wall reads the corner directly: 90° in a square room, 135° at each corner of a bay. Inside and outside corners are measured the same way.

  2. 02

    Halve it

    The joint lies on the line that splits the corner. For flat trim that line is the cut: 90° − corner ÷ 2, so 45° for a square corner and 44° for a 92° one.

  3. 03

    Account for the spring

    Crown sits at its spring angle, 38° off the wall for 52/38 crown. Lying flat on the saw, the cut needs a miter and a bevel; nested at the spring angle against the fence it needs only the plain miter.

  4. 04

    Find the long point

    At an inside corner the edge against the wall is longest; at an outside corner the face (or the ceiling edge of crown) is. The face edge loses or gains depth ÷ tan(corner ÷ 2) at each end.

  5. 05

    Test, then cut

    Cut a pair from offcuts and hold them in the corner. At an inside corner, a gap at the face means the corner is wider than you measured and a gap at the back means tighter; at an outside corner it is the other way round.

Good to know

Miter angle and crown molding angle questions

For flat trim — baseboard, casing, chair rail, a picture frame — 45° on each piece, cut in opposite directions so they close into 90°. For crown molding the answer depends on how it sits in the saw: 45° nested upside down against the fence, or 31.62° miter with a 33.86° bevel lying flat (52/38 crown).

Because it leans. Crown sits between the wall and the ceiling at its spring angle, so the cut that meets the corner's center line crosses the molding at a slant. Stood up in the saw at that same lean (nested), the cut is 45°; laid flat, it becomes a compound cut with a smaller miter and a bevel.

The angle between the back of the crown and the wall. Most crown sold at Home Depot and Lowe's is 52/38: it springs 38° off the wall and 52° off the ceiling. Some is 45/45. To find it on a piece you have, set it in a framing square as it sits on the wall: spring = arctan(projection ÷ drop).

No: the saw settings are the same numbers for the same corner angle. What changes is which way the blade swings and which edge is long. At an inside corner the edge against the wall is the long point; at an outside corner the face, or the ceiling edge of crown, is.

For a bay window or an octagon, with 52/38 crown lying flat: 14.31° miter and 17.55° bevel. With 45/45 crown: 16.32° and 15.70°. Nested upside down, any crown is a 22.5° miter with no bevel.

Measure it and use the real number. A 92° corner takes 44° on baseboard and 30.73° / 33.19° on 52/38 crown; an 88° corner takes 46° and 32.52° / 34.53°. Splitting the error evenly between the two pieces keeps the profile lined up.

180° divided by the number of sides: 30° for a hexagon, 22.5° for an octagon, 36° for a pentagon. Cut both ends of every piece at that angle, long points on the outside edge.

A coped inside corner stays closed when the house moves and the wood shrinks: the first piece runs square into the corner, the second gets this page's inside miter and is then sawn back along the profile line with a coping saw, so it laps over the first piece's face. Outside corners are always mitered; on stained work some carpenters cope and some miter and glue.

For your website

Run a contractor, supply or DIY site? Put this miter and crown molding angle calculator on your own page for free — it works the same as here and updates on its own.

Keep estimating